

NANOESP32-C6 Development Board | ESP32-C6-WROOM-1-N4 | WiFi 6 + Zigbee + Thread | RISC-V 160MHz | 4MB Flash | Dual USB-C | RGB LED
The nanoESP32-C6 development board puts Espressif's ESP32-C6 - their first Wi-Fi 6 SoC - on a breadboard-friendly board with two USB Type-C ports and every…
- Delivery in 2 to 4 working daysFree in Islamabad & Rawalpindi above Rs 5,000
- Cash on deliveryPay when your parcel arrives
- 7-day checking warrantyDead-on-arrival items replaced
- Packed with careAnti-static & padded packaging
Highlights
- 🔗 Bluetooth 5.3 LE certified - long range, 2 Mbps PHY and advertising extensions for BLE mesh and beacon work.
- 📌 Headers pre-soldered - 2.54 mm pins on both rows, ready for a breadboard straight out of the bag.
- 📡 Built-in PCB antenna - no external antenna or connector needed.
- 🔘 BOOT and RST buttons - manual download mode and reset without shorting pins.
- 1 × nanoESP32-C6 development board, ESP32-C6-WROOM-1-N4, pin headers pre-soldered - tested and QC-OK
- ESP32-C6 Datasheet by Espressif
- ESP32-C6 ESP-IDF get-started guide
- ESP32-C6 SoC product page by Espressif
Specifications
- Module
- ESP32-C6-WROOM-1-N4 (PCB antenna)
- SoC
- Espressif ESP32-C6
- HP processor
- 32-bit RISC-V, up to 160 MHz
- LP processor
- 32-bit RISC-V, up to 20 MHz
- Flash
- 4 MB SPI flash (no PSRAM)
- SRAM
- 512 KB HP SRAM + 16 KB LP SRAM
- ROM / cache
- 320 KB ROM, 32 KB L1 cache
- Wi-Fi
- 802.11ax (Wi-Fi 6) 2.4 GHz, 1T1R, 2412-2484 MHz, up to 150 Mbps; backward compatible with 802.11b/g/n
- Bluetooth
- Bluetooth 5.3 LE certified
- USB
- 2 × USB Type-C - CH343P USB-UART (COM) and native USB Serial/JTAG (USB)
- GPIO
- 30 programmable GPIOs (QFN40 package)
- ADC
- 12-bit SAR ADC, up to 7 channels
- PWM
- LED PWM up to 6 channels, plus Motor Control PWM (MCPWM)
- Timers and sensors
- on-chip temperature sensor, pulse counter, 52-bit system timer, 2 × 54-bit general-purpose timers
About this product
The nanoESP32-C6 development board puts Espressif's ESP32-C6 - their first Wi-Fi 6 SoC - on a breadboard-friendly board with two USB Type-C ports and every usable GPIO brought out to 2.54 mm headers. One port runs through a CH343P USB-to-UART bridge for flashing and serial monitoring; the other is the ESP32-C6's own native USB, so you get USB Serial/JTAG debugging without an external probe.
What makes the C6 worth picking over an older ESP32 is the radio. A single chip covers 2.4 GHz Wi-Fi 6 (802.11ax), Bluetooth 5.3 LE and IEEE 802.15.4 - which means Thread 1.3, Zigbee 3.0 and a direct path to Matter. For a smart-home sensor, a Zigbee node, or a battery-powered device that needs Target Wake Time to stretch its runtime, this is the board to prototype on.
Key Features
•📶 Wi-Fi 6 on 2.4 GHz - 802.11ax with OFDMA and Target Wake Time for lower power draw and better behaviour on crowded networks, still backward compatible with 802.11b/g/n.
•🏠 Thread 1.3 and Zigbee 3.0 - an on-chip IEEE 802.15.4 radio, so one board can act as a Matter end device or a Zigbee node with no second module.
•⚡ Two RISC-V cores - a 160 MHz high-performance core for your application plus a 20 MHz low-power core that keeps running while the main core sleeps.
•🔌 Dual USB Type-C - the COM port goes through a WCH CH343P bridge for flashing and serial; the USB port is the ESP32-C6's native USB Serial/JTAG.
•🌈 Addressable RGB LED on GPIO8 - WS2812-style, driven by Adafruit_NeoPixel or the ESP-IDF LED strip component. Status output with nothing to wire.
•📡 Built-in PCB antenna - no…
Related searches
You may also need
More Smart Home →








